Detection, mapping and estimation of rate of spread of grass fires from southern African ERTS-1 imagery

Sequential band-6 imagery of the Zambesi Basin of southern Africa recorded substantial changes in burn patterns resulting from late dry season grass fires. One example from northern Botswana, indicates that a fire consumed approximately 70 square miles of grassland over a 24-hour period. Another example from western Zambia indicates increased fire activity over a 19-day period. Other examples clearly define the area of widespread grass fires in Angola, Botswana, Rhodesia and Zambia. From the fire patterns visible on the sequential portions of the imagery, and the time intervals involved, the rates of spread of the fires are estimated and compared with estimates derived from experimental burning plots in Zambia and Canada. It is concluded that sequential ERTS-1 imagery, of the quality studied, clearly provides the information needed to detect and map grass fires and to monitor their rates of spread in this region during the late dry season

An investigation into the behaviour of air rifle pellets in ballistic gel and their interaction with bone

Although air weapons are considerably lower in power than other firearms, there is increasing concern that serious injuries can result from their misuse. The present study was therefore carried out to improve understanding of the terminal ballistic behaviour of air rifle pellets. Pellets were fired into ballistic gel under a variety of conditions. The pellets penetrated further than anticipated from their low cross-sectional density, and Bloom number was not necessarily a good guide to gel behaviour. Pellet penetration into the gel decreased with increasing gel concentration, and appeared to be linear at higher concentrations. Pointed pellets penetrated up to 50% further than rounded pellets. Power and range affect penetration, but other factors are also important, and power alone is not a simple guide to potential penetration. Test firings were also carried out firing pellets into ballistic gel that contained sections of animal bone. Computed tomography (CT) and visual observation were employed to record the interactions. CT scanning showed potential as a tool for examining pellet damage. The bone appeared to be undamaged, but the pellets were severely deformed on impact. If the pellet strikes the bone at an angle, less energy is absorbed by the impact and the pellet fragments may ricochet and cause further damage in the gel. A tentative model is proposed for estimating the energy absorbed by the impact

The interaction between clothing and air weapon pellets

Comparatively few studies have been carried out on air weapon injuries yet there are significant number of injuries and fatalities caused by these low power weapons because of their availability and the public perception that because they need no licence they are assumed to be safe. In this study ballistic gel was tested by Bloom and rupture tests to check on consistency of production. Two series of tests were carried out firing into unclothed gel blocks and blocks loosely covered by different items of clothing to simulate attire (tee shirt, jeans, fleece, and jacket).The damage to the clothing caused by different shaped pellets when fired at different ranges was examined. The apparent hole size was affected by the shape of pellet (round, pointed, flat and hollow point) and whether damage was predominantly caused by pushing yarn to one side or by laceration of the yarn through cutting or tearing.The study also compared penetration into clothed gel and unclothed gel under identical conditions, and loose clothing greatly reduced penetration. With loose clothing at 9.1 m range clothing reduced penetration to 50–70% of the penetration of unclothed gel but at 18.3 m range only 7 out of 36 shots penetrated the gel. This cannot be accounted for by the energy loss at the longer range (3–7% reduction from 9.1 m to 18.3 m range in unclothed gels) and it is suggested that impulse may have a role to play.Shots that did not penetrate the gel were used to estimate the possible stopping time for the pellet (around 75 μs) and force (1700 N) or stress (100 MPa) required to bring the pellet to a halt.Even with these low energy projectiles, cloth fibres were entrained in the gel showing the potential for penetration of the body and subsequent infection

A fundamental approach to adhesion: Synthesis, surface analysis, thermodynamics and mechanics

The acid-base properties of titanium 6-4 plates (low surface area) were investigated after three different pretreatments, namely Turco, phosphate-fluoride and Pasa-Jell. A series of indicators was used and color changes were detected using diffuse reflectance visible spectroscopy. Electron spectroscopy for chemical analysis was used to examine the indicator on the Ti 6-4 surface. Specular reflectance infra-red spectroscopy was used to study the adsorption of stearic acid from cyclohexane solutions on the Ti 6-4 surface

A critical study of the role of the surface oxide layer in titanium bonding

The molecular understanding of the role which the surface oxide layer of the adherend plays in titanium bonding is studied. The effects of Ti6-4 adherends pretreatment, bonding conditions, and thermal aging of the lap shear specimens were studied. The use of the SEM/EDAX and ESCA techniques to study surface morphology and surface composition was emphasized. In addition, contact angles and both infrared and visible reflection spectroscopy were used in ancillary studies

A fundamental approach to adhesion: Synthesis, surface analysis, thermodynamics and mechanics

Adherend surfaces and fractography were studied using electron spectroscopy for chemical analysis and scanning electron microscopy/energy dispersive analysis of X-rays. In addition, Auger Electron Spectroscopy with depth profiling capability was used. It is shown that contamination of adhesion systems plays an important role not only in determining initial bond strengths but also in the durability of adhesive bonds. It is concluded that the analytical techniques used to characterize and monitor such contamination

A critical study of the role of the surface oxide layer in titanium bonding

Scanning electron microscope/X-ray photoelectron spectroscopy (SEM/XPS) analysis of fractured adhesively bonded Ti 6-4 samples is discussed. The text adhesives incuded NR 056X polyimide, polypheylquinoxaline (PPQ), and LARC-13 polyimide. Differentiation between cohesive and interfacial failure was based on the absence of presence of a Ti 2p XPS photopeak. In addition, the surface oxide layer on Ti-(6A1-4V) adherends is characterized and bond strength and durability are addressed. Bond durability in various environmental conditions is discussed

Interaction of hydrogen chloride with alumina

The influence of temperature, pressure, and outgas conditions on the absorption of hydrogen chloride and water vapor on both alpha and gamma alumina was studied. Characterization of the adsorbents was performed using X-ray powder diffraction, scanning electron microscopy (SEM), low temperature nitrogen adsorption desorption measurements, BET nitrogen surface area measurements and electron spectroscopy for chemical analysis (ESCA). Water vapor adsorption isotherms at 30, 40, and 50 C were measured on alpha and gamma alumina after outgassing at 80, 200, and 400 C. Both outgas temperature and adsorption temperature influenced the adsorption of water vapor on the aluminas. The water vapor adsorption was completely reversible. Alpha alumina absorbed more water per unit area than gamma alumina. Differences in the adsorption capacity for water vapor of the two aluminas were explained on the basis of ideal surface models of alpha and gamma alumina. Isosteric heats of adsorption for water vapor on the aluminas were determined over a limited range of surface coverage

Surface analysis in composite bonding

X ray photoelectron spectroscopy and contact angle measurements on graphite fiber composites pretreated in a number of different ways including mechanical, chemical, and light irradiation were analyzed. Data acquired on surface contamination as a result of fabrication techniques provides answers to the strength and durability of adhesively bonded composites. These techniques were shown to provide valuable information on surface analysis of pretreated composites prior to adhesive bonding and following lap shear fracture

Interaction of hydrogen chloride with alumina

The influence of outgas conditions and temperature on the adsorptive properties of two aluminas Alon-c and Al6sG were studied using adsorption isotherm measurements. Alon-C and Al6SG were characterized using X-ray powder diffraction, thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and BET nitrogen surface areas. Some of these techniques were applied to two other aluminas but no isotherm data was obtained. Isotherm data and techniques applied to each alumina are summarized in tabular form